2.7.07 Sistemas de acoplamento de reboques
Aprenda as etapas seguras de acoplamento, verificação e desacoplamento de reboques e semirreboques. Concentre-se especialmente na folga, travamento, dispositivos de suporte, conexões de mangueira e limites de desgaste.
1. A regra de ouro da segurança
Uma barra de tração ou engate de reboque não deve ter folga longitudinal perceptível.
A folga longitudinal pode danificar a travessa/travessa final e pode fazer com que o acoplamento do reboque ou o reboque se solte.
- A folga final em um acoplamento de reboque não é permitida.
- A folga longitudinal na barra de tração do reboque deve ser corrigida imediatamente.
- Brincadeiras nas buchas dos rolamentos causam impactos e danos.
- A sobrecarga dos pneus não é a consequência relevante nestas questões.
2. Acoplar um trailer normal
- Coloque a barra de tração na altura de engate usando o ajuste de altura do reboque.
- Dê ré com cuidado no veículo rebocador em direção ao trailer.
- Certifique-se de que ninguém esteja entre o veículo e o trailer.
- O solo pode ser tocado durante o processo de acoplamento.
- Verifique se a garra do acoplamento fecha com segurança.
- Levante e prenda a roda de suporte antes de dirigir.
- Após o acoplamento, solte o freio de estacionamento do reboque e remova os calços das rodas.
3. Reboque multieixo com engate automático
- Verifique se o pino de acoplamento está totalmente encaixado.
- Verifique a posição do pino de controle.
- A barra de tração deve estar corretamente ajustada.
- O reboque deve ser protegido contra deslocamento com freio de estacionamento e/ou calços.
- O ângulo de inclinação da barra de tração geralmente não é o foco do exame aqui.
Dica de exame:
Perguntas sobre engate automático geralmente são feitas sobre o pino de controle e o pino de acoplamento totalmente engatado.
4. Ordem de conexão da mangueira do freio a ar
Com cabeças de acoplamento combinadas
Ambas as linhas fecham/conectam ao mesmo tempo.
Sem cabeças de acoplamento combinadas
Conecte primeiro a linha do freio: cabeçote de acoplamento amarelo.
Nunca conecte peças de acoplamento de cores diferentes incorretamente.
5. Acoplar um semirreboque
- A quinta roda deve ser destravada e aberta antes do acoplamento.
- A quinta roda e o pino mestre devem estar aproximadamente na mesma altura.
- Após o acoplamento, verifique o sistema de travamento e segurança da quinta roda.
- Verifique se a fechadura fecha automaticamente.
- Conecte e verifique todas as conexões de mangueiras e cabos.
6. Desacoplando um semirreboque
- Prenda as rodas do semirreboque.
- Estenda as pernas de apoio/dispositivos de apoio.
- Desconecte todas as conexões de mangueiras e cabos entre o trator e o semirreboque.
- Destrave e abra a trava da quinta roda.
7. Limites de desgaste e verificações técnicas
| Peça / cheque | O que lembrar |
|---|---|
| Folga de altura do pino de acoplamento | Folga máxima de 4 mm. Muito alto pode causar solavancos; muito baixo pode impedir o engate adequado. |
| Diâmetro do parafuso de acoplamento | Não deve ser inferior a 36,5 mm em toda a superfície de acoplamento. Substitua se estiver muito gasto. |
| Óculos com barra de tração | Desgaste máximo do diâmetro: 1,5 mm. |
| Teste de desgaste da barra de tração / anel giratório | Com o reboque travado, mova o veículo trator para a frente brevemente várias vezes para detectar desgaste perigoso. |
| Guia de fixação inferior | Não deve haver jogo excessivo. |
Sistema de acoplamento K 80
Após o acoplamento, trave o dispositivo de fixação e ajuste a altura de acoplamento do reboque ao reboque.
O sistema K 80 não necessita de lubrificação antes de cada utilização.
Verificação do pino de controle
Você pode verificar o engate correto observando o pino de controle ou a luz indicadora na cabine.
Segurança das pessoas
Ao fazer marcha-atrás, preste sempre atenção às pessoas que possam estar entre o veículo e o reboque.
Lista de verificação rápida para exames
Perguntas de Prática (23)
-
Pergunta 1 de 23
What control and service work has to be carried out regularly on a fifth wheel?
2.7.07-2013 Pontos -
Pergunta 2 de 23
What must you consider when coupling a trailer with ball coupling?
2.7.07-2083 PontosExplicação
When coupling a trailer you have to make sure that the existing support wheel is raised before departure and secured. The coupling claw has to close securely. The ground is touched during the coupling process.
-
Pergunta 3 de 23
What must be checked after you have coupled a multiple-axle trailer to an automatic trailer coupling?
2.7.07-2093 PontosExplicação
When coupling a multi-axle trailer to an automatic trailer hitch, you should check that the coupling pin is fully engaged and the position of the control pin is checked. The angle of inclination of the trailer drawbar does not need to be checked.
-
Pergunta 4 de 23
What must you do after attaching a semitrailer?
2.7.07-3024 PontosExplicação
After hitching a semitrailer you should produce and check and check the lock and security system of the fifth wheel, whether this closes automatically all hose and cable connections.
-
Pergunta 5 de 23
What is the maximum vertical play permitted for a coupling pin?
2.7.07-3033 PontosExplicação
The coupling pin must have a maximum height of 4 mm play. If it is too high, it jerky. If it is too low, the bolt when closing the clutch can not engage more.
-
Pergunta 6 de 23
You take over a semitrailer which you have not used before. What must you remember before attaching the semitrailer?
2.7.07-3044 Pontos -
Pergunta 7 de 23
What must you do before detaching a semitrailer?
2.7.07-3053 PontosExplicação
All three answers are correct. All hose and cable connections zwichen tractor and semi-trailer separate the clutch lock unlocked and opened the lock of the fifth wheel and determine finally, the wheels of the semitrailer and extend the support means.
-
Pergunta 8 de 23
What is the correct procedure when coupling up a multiple-axle trailer?
2.7.07-3064 PontosExplicação
During the coupling of the towing vehicle is Mehrachsanhängers ranks to the trailer. Please Eighth also people who may be located in between.
-
Pergunta 9 de 23
What must you check before coupling up a multiple-axle trailer?
2.7.07-3094 PontosExplicação
During the coupling of a multi-axle trailer, you need to convince them that the drawbar adjusted properly and whether the trailers are secured against rolling off (parking brake, wheel chocks) you
-
Pergunta 10 de 23
How can you see that the coupling pin has engaged correctly in the case of an automatic trailer coupling?
2.7.07-3124 PontosExplicação
So you can check whether the coupling pin is properly engaged, you can look up or look at the indicator light in the cab of the control pin of the coupling.
-
Pergunta 11 de 23
What is the maximum play the towing fork may have in the bearing bushes in towing direction?
2.7.07-3153 PontosExplicação
The drawbar must not have any noticeable play in the bearing bushes (tensile direction). This could cause shock to the bushings.
-
Pergunta 12 de 23
What can be the consequences if the tow-bar of a towing coupling has longitudinal play?
2.7.07-3174 PontosExplicação
The consequences of the longitudinal play of the pull rod are as follows: cracking at the cross arm, to which the trailer coupling is secured and pulling the trailer coupling.
-
Pergunta 13 de 23
How do you have to disconnect the air lines when detaching a trailer?
2.7.07-3193 Pontos -
Pergunta 14 de 23
What must you remember when coupling up a trailer?
2.7.07-3203 PontosExplicação
When coupling a trailer with a combined coupling heads close both lines at the same time and connect without combined heads the first brake line (yellow coupling head)
-
Pergunta 15 de 23
What must you remember when coupling up a trailer?
2.7.07-3213 PontosExplicação
When coupling a trailer, please release the parking brake after coupling and remove different colored chocks coupling parts must not be connected.
-
Pergunta 16 de 23
What must you remember after you have coupled up a trailer to an automatic trailer coupling?
2.7.07-3224 PontosExplicação
(Automatically) to autonomously functioning, trailer hitch you should pay attention to the position of the control pin and the coupling pin must be fully engaged.
-
Pergunta 17 de 23
Which requirements must be fulfilled before coupling a semi-trailer?
2.7.07-3234 PontosExplicação
be unlocked during coupling of a semitrailer has the fifth wheel (tractor) and opened our fifth wheel and kingpin (semitrailers) must be something on the same level.
-
Pergunta 18 de 23
The coupling pins of your trailer hitch have a diameter of 38 mm when new. What should you note regarding wear?
2.7.07-3243 PontosExplicação
If you notice wear on the coupling bolt (e.g. 2 mm) you have to have the bolt replaced, because the diameter must not be less than 36.5 mm on the entire circumference of the coupling surface. There must also be no excessive play in the lower fastener guide.
-
Pergunta 19 de 23
A considerable amount of longitudinal play becomes apparent in the towing device of the trailer. What effect can this have?
2.7.07-3253 PontosExplicação
If you notice significant longitudinal play in the trailer drawbar, this will affect the final cross member of the towing vehicle (damage) and the trailer can tear off.
-
Pergunta 20 de 23
How much longitudinal play may there be in the drawbar of the hitch?
2.7.07-3263 PontosExplicação
A longitudinal play in the drawbar of your trailer is not permitted and must be remedied immediately.
-
Pergunta 21 de 23
The drawbar of a full trailer is to be kept level with the coupling height of the approaching towing vehicle. How is this ensured?
2.7.07-3273 PontosExplicação
To bring the drawbar of a drawbar trailer to coupling height, use the height adjustment of the trailer.
-
Pergunta 22 de 23
How can you check the state of wear of the drawbar or the turntable of a full trailer?
2.7.07-3283 PontosExplicação
You can check with your towing vehicle whether there is any wear on the drawbar or the slewing ring of the trailer by starting briefly when the trailer is secured with the parking brake.
-
Pergunta 23 de 23
What is the maximum permissible wear measured across the diameter of the towing ring of a drawbar?
2.7.07-3303 PontosExplicação
The diameter must not exceed 1.5 mm.