2.7.07 Trailer coupling systems
Learn the safe coupling, checking, and uncoupling steps for trailers and semitrailers. Focus especially on play, locking, support devices, hose connections, and wear limits.
1. The golden safety rule
A drawbar or tow coupling must not have noticeable longitudinal play.
Longitudinal play can damage the final cross member/traverse and may cause the trailer coupling or trailer to tear off.
- End play in a tow coupling is not permitted.
- Longitudinal play in the trailer drawbar must be fixed immediately.
- Play in bearing bushes causes impacts and damage.
- Tyre overload is not the relevant consequence in these questions.
2. Coupling a normal trailer
- Bring the drawbar to coupling height using the trailer height adjustment.
- Reverse the towing vehicle carefully toward the trailer.
- Make sure nobody is standing between vehicle and trailer.
- The ground may be touched during the coupling process.
- Check that the coupling claw closes securely.
- Raise and secure the support wheel before driving.
- After coupling, release the trailer parking brake and remove wheel chocks.
3. Multi-axle trailer with automatic hitch
- Check that the coupling pin is fully engaged.
- Check the position of the control pin.
- The drawbar must be correctly adjusted.
- The trailer must be secured against rolling away with parking brake and/or chocks.
- The inclination angle of the drawbar is usually not the exam focus here.
Exam tip:
Automatic hitch questions often ask about the control pin and fully engaged coupling pin.
4. Air brake hose connection order
With combined coupling heads
Both lines close/connect at the same time.
Without combined coupling heads
Connect the brake line first: yellow coupling head.
Never connect coupling parts of different colours incorrectly.
5. Coupling a semitrailer
- The fifth wheel must be unlocked and opened before coupling.
- The fifth wheel and kingpin should be approximately at the same height.
- After coupling, check the fifth-wheel locking and safety system.
- Check that the lock closes automatically.
- Connect and check all hose and cable connections.
6. Uncoupling a semitrailer
- Secure the semitrailer wheels.
- Extend the support legs/support devices.
- Disconnect all hose and cable connections between tractor and semitrailer.
- Unlock and open the fifth-wheel lock.
7. Wear limits and technical checks
| Part / check | What to remember |
|---|---|
| Coupling pin height play | Maximum 4 mm play. Too high can cause jerking; too low can prevent proper engagement. |
| Coupling bolt diameter | Must not be less than 36.5 mm over the whole coupling surface. Replace if worn too much. |
| Drawbar eye wear | Maximum diameter wear: 1.5 mm. |
| Drawbar / slewing ring wear test | With trailer braked, move the towing vehicle forward briefly several times to detect dangerous wear. |
| Lower fastener guide | There must be no excessive play. |
K 80 coupling system
After coupling, lock the hold-down device and adjust the trailer coupling height to the trailer.
The K 80 system does not need lubrication before every use.
Control pin check
You can check correct engagement by looking at the control pin or the indicator light in the cab.
People safety
When reversing to couple, always pay attention to people who may be standing between the vehicle and trailer.
Fast exam checklist
Practice Questions (23)
-
Question 1 of 23
What control and service work has to be carried out regularly on a fifth wheel?
2.7.07-2013 Points -
Question 2 of 23
What must you consider when coupling a trailer with ball coupling?
2.7.07-2083 PointsExplanation
When coupling a trailer you have to make sure that the existing support wheel is raised before departure and secured. The coupling claw has to close securely. The ground is touched during the coupling process.
-
Question 3 of 23
What must be checked after you have coupled a multiple-axle trailer to an automatic trailer coupling?
2.7.07-2093 PointsExplanation
When coupling a multi-axle trailer to an automatic trailer hitch, you should check that the coupling pin is fully engaged and the position of the control pin is checked. The angle of inclination of the trailer drawbar does not need to be checked.
-
Question 4 of 23
What must you do after attaching a semitrailer?
2.7.07-3024 PointsExplanation
After hitching a semitrailer you should produce and check and check the lock and security system of the fifth wheel, whether this closes automatically all hose and cable connections.
-
Question 5 of 23
What is the maximum vertical play permitted for a coupling pin?
2.7.07-3033 PointsExplanation
The coupling pin must have a maximum height of 4 mm play. If it is too high, it jerky. If it is too low, the bolt when closing the clutch can not engage more.
-
Question 6 of 23
You take over a semitrailer which you have not used before. What must you remember before attaching the semitrailer?
2.7.07-3044 Points -
Question 7 of 23
What must you do before detaching a semitrailer?
2.7.07-3053 PointsExplanation
All three answers are correct. All hose and cable connections zwichen tractor and semi-trailer separate the clutch lock unlocked and opened the lock of the fifth wheel and determine finally, the wheels of the semitrailer and extend the support means.
-
Question 8 of 23
What is the correct procedure when coupling up a multiple-axle trailer?
2.7.07-3064 PointsExplanation
During the coupling of the towing vehicle is Mehrachsanhängers ranks to the trailer. Please Eighth also people who may be located in between.
-
Question 9 of 23
What must you check before coupling up a multiple-axle trailer?
2.7.07-3094 PointsExplanation
During the coupling of a multi-axle trailer, you need to convince them that the drawbar adjusted properly and whether the trailers are secured against rolling off (parking brake, wheel chocks) you
-
Question 10 of 23
How can you see that the coupling pin has engaged correctly in the case of an automatic trailer coupling?
2.7.07-3124 PointsExplanation
So you can check whether the coupling pin is properly engaged, you can look up or look at the indicator light in the cab of the control pin of the coupling.
-
Question 11 of 23
What is the maximum play the towing fork may have in the bearing bushes in towing direction?
2.7.07-3153 PointsExplanation
The drawbar must not have any noticeable play in the bearing bushes (tensile direction). This could cause shock to the bushings.
-
Question 12 of 23
What can be the consequences if the tow-bar of a towing coupling has longitudinal play?
2.7.07-3174 PointsExplanation
The consequences of the longitudinal play of the pull rod are as follows: cracking at the cross arm, to which the trailer coupling is secured and pulling the trailer coupling.
-
Question 13 of 23
How do you have to disconnect the air lines when detaching a trailer?
2.7.07-3193 Points -
Question 14 of 23
What must you remember when coupling up a trailer?
2.7.07-3203 PointsExplanation
When coupling a trailer with a combined coupling heads close both lines at the same time and connect without combined heads the first brake line (yellow coupling head)
-
Question 15 of 23
What must you remember when coupling up a trailer?
2.7.07-3213 PointsExplanation
When coupling a trailer, please release the parking brake after coupling and remove different colored chocks coupling parts must not be connected.
-
Question 16 of 23
What must you remember after you have coupled up a trailer to an automatic trailer coupling?
2.7.07-3224 PointsExplanation
(Automatically) to autonomously functioning, trailer hitch you should pay attention to the position of the control pin and the coupling pin must be fully engaged.
-
Question 17 of 23
Which requirements must be fulfilled before coupling a semi-trailer?
2.7.07-3234 PointsExplanation
be unlocked during coupling of a semitrailer has the fifth wheel (tractor) and opened our fifth wheel and kingpin (semitrailers) must be something on the same level.
-
Question 18 of 23
The coupling pins of your trailer hitch have a diameter of 38 mm when new. What should you note regarding wear?
2.7.07-3243 PointsExplanation
If you notice wear on the coupling bolt (e.g. 2 mm) you have to have the bolt replaced, because the diameter must not be less than 36.5 mm on the entire circumference of the coupling surface. There must also be no excessive play in the lower fastener guide.
-
Question 19 of 23
A considerable amount of longitudinal play becomes apparent in the towing device of the trailer. What effect can this have?
2.7.07-3253 PointsExplanation
If you notice significant longitudinal play in the trailer drawbar, this will affect the final cross member of the towing vehicle (damage) and the trailer can tear off.
-
Question 20 of 23
How much longitudinal play may there be in the drawbar of the hitch?
2.7.07-3263 PointsExplanation
A longitudinal play in the drawbar of your trailer is not permitted and must be remedied immediately.
-
Question 21 of 23
The drawbar of a full trailer is to be kept level with the coupling height of the approaching towing vehicle. How is this ensured?
2.7.07-3273 PointsExplanation
To bring the drawbar of a drawbar trailer to coupling height, use the height adjustment of the trailer.
-
Question 22 of 23
How can you check the state of wear of the drawbar or the turntable of a full trailer?
2.7.07-3283 PointsExplanation
You can check with your towing vehicle whether there is any wear on the drawbar or the slewing ring of the trailer by starting briefly when the trailer is secured with the parking brake.
-
Question 23 of 23
What is the maximum permissible wear measured across the diameter of the towing ring of a drawbar?
2.7.07-3303 PointsExplanation
The diameter must not exceed 1.5 mm.